How to Enable Toggle Keys of your Systems?

How to Enable Toggle Keys of your Systems?



    Toggle Keys option designed for those people who are typing while looking away from the screen or for those who are vision impairment. When your system Toggle keys is turned on, you will get a special sound when special keys are pressed like CAPS, NUM, SCROLL LOCK keys.

    

    To enable or disable your system Toggle keys, go to Control Panel using Start button. In your system Control Panel normally the first option will be Accessibility options. Double click on Accessibility options and check the Toggle keys box, Windows will automatically send you a special beeps when you will press locking keys.

Read More

How To Solve “Power Calibration Error”

How To Solve “Power Calibration Error”

The “Power Calibration Error” typically appears when you are attempting to burn a CD or DVD, and the burner fails to write the CD or DVD. The error might also appear as a “Medium Speed Error.”

There are multiple reasons that could cause the error, but the error is most likely to occur because the CD/DVD burner is not able to determine the Optimum Power Calibration rate. The Optimum Power Calibration rate is a test that is run before burning a CD or DVD to determine the optimal laser power needed to write the CD or DVD, and when this is not able to be determined the disk burn fails. The “Power Calibration Error” can also appear for minor reasons that can be easily fixed.

Options for Fixing “Power Calibration Error”

It is very difficult to figure out exactly what caused the “Power Calibration Error.” There are a few possible ways to fix it, so your best option is to try the different fixes until one works for you.

Use the options below to fix the “Power Calibration Error.”

1. A common reason for this error to appear is cheap blank media. Try using different brands of quality blank media to solve the error. Some good brands to use are JVC, Verbatim, and Falcon.
2. It is usually very effective to burn at lower speeds.
3. It is a good idea to check with Sony to find out if there is a firmware upgrade for your CD or DVD.
4. You can also try updating your CD/DVD burning software to the most recent version.
5. You can try cleaning the disk drive. Make sure there are no dust particles or bits of paper.
6. Iftheoptionsabovedonotwork, thenyoucandisableImageMasteringApplicationsProgrammingInterface (IMAPI)Service. ThisservicemanagesCDandDVDrecordings. TodisableIMAPIservice, followthesesteps:

a. Launch the Control Panel, click on Administrative Tools, then click on Services.

b. Browse for “IMAPI CD-Burning COM Service.” Once you find it, right-click on it and select Properties.

c. Change the Startup Type to Disabled.

d. Click on Apply and then Reboot.

7. If none of the above options work for you, then it is most likely a hardware problem and not a software problem. At this point, it is a good idea to get your burner laser lens cleaned professionally.
8. If every option fails, then the driver’s laser probably died and it will need to be replaced.

Read More

How to hiding icons on the bottom of your screen?

How to hiding icons on the bottom of your screen?



By using this tip you can hide the useless icons on the bottom of your system screen (right end of the taskbar). Because some of the icons will useful for you on system tray area but may be others list of icons not useful for you so you can hide all extra icon very easily. Many programs that run in the background on your computer but you are not using regularly such as antivirus software, volume controller, backup applications. The system tray can get cluttered with useless icon, so you may not wants to display them on the tray.

To hide those icons that you do not use regularly, follow these steps.
First of all right-click on the windows taskbar and choose Properties.

Here a new dialog box will appear with title "Taskbar and start Menu Properties" and then click on "Customize…"button that appears on lower right portion.

Now again a new dialog box will appear with title "Customize Notifications".

Under Current Items area, select the program that you want to change the behavior. On the right of the program name a drop-down menu appears for example "Always hide, Always show and Hide when inactive".

You choose to hide the program’s Icon, when it is inactive, to always hide the icon, or to always show it.

Select the option you want and click on OK button, then again click on OK button to finish the process.

Read More

How you Export and Import Registry File Before Editing ?

How you Export and Import Registry File Before Editing ?



    Today an important tip about the back up of your system Registry. Make sure before modifying your system Registry about its backup because Registry contains all information how your system runs. This backup will help you to restore Registry in case any problem occurs after modifying.

    You can backup the whole Registry and also Registry subkeys.
    Click Start Button then type regedit in Run box and click Ok button. Here you can export the whole Registry or you can locate the required subkeys that contain the information that you want to edit.

    Go to File menu option then click on Export option for backup and save it with on any your system drive with .reg extension and you can restore this backup going File menu using import option.

Read More

More Control Over Your Computer's Boot Process

More Control Over Your Computer's Boot Process

    You can set the boot time in windows XP as your wish if you are install two operating systems on same computer, for example window 2000 with windows XP or more than two. Yow can do this with editing  Boot.ini file. Here you can also set  the sequence for operating system which operating system boot first.

    





    First Right Click on My Computer option and then select its Properties. In next dialog box open Advanced tab button. Under Startup and Recovery, click on the Settings button. Use the spin box "Time to display list of operating systems" to set the number of seconds you want the system to wait before automatically starting the default operating system. Here you will set time in seconds and its range start from 0 and ends with 999 seconds.

    After set the time, then click OK option to close the dialog box to save your change. The next time you restart, the new time will take effect.

Read More

How to Fix Error 0×80070570

How to Fix Error 0×80070570

Error code 0×80070570 is one of the most common errors on computers. The error typically shows up on the screen as a message. It is important to repair the computer as soon as a message with this error code appears on the screen of the computer. The error can cause serious damage to the system. It makes the computer performance slow and inefficient. The error also locks up programs and freezes up the computer hardware.

Error code 0×80070570 can occur for multiple reasons. The most common occurrence of the error message is when you set up the Microsoft updates on your computer. The error code can show up when you try to set up updates for Windows programs or when Windows gadgets are automatically updated.

The error code can also occur when an important file is corrupt or not correct. It is possible that the error code will appear if some of your deleted files are still on your computer but not readable by Windows. The error code could also occur if your computer will not allow you to move or delete files in the folder documents.

Prevention of Error 0×80070570

It is important to make sure that you install effective anti-virus protection software. Microsoft Security Essentials is a reliable and efficient open-source product that is good to use. Make sure that you always keep your anti-virus protection software up to date.

If you do not have a good anti-virus product, then viruses can destroy files on your computer which will lead to error code 0×80070570 appearing. Always make sure that your computer is secured from viruses to prevent error 0×80070570 or other harmful errors from occurring.

How to Fix Error 0×80070570 with Error Repair Tool

One way to fix Error 0×80070570 is to run the Error Repair Tool. This will automatically correct the error. Follow these simple steps to fix error 0×80070570 with the Error Repair Tool:

   1. Gotohttp://error0x80070570.com/go-6.phptodownloadtheErrorRepairTool. Aboxwillpopuponthewebsiteaskingyoutosavethefile. Savethefileandthendownloadandrunthefile.
   2. After you download the file, click the SCAN button.
   3. Click the REPAIR button to fix your errors.

How to Fix Error 0×80070570 by Cleaning the Registry

If the Error Repair Tool does not work, then there is the option of setting up a registry cleaner. Your registry contains the files that are on your computer. The registry can corrupt when a file is damaged. The registry can also corrupt when the installation of a program is running and it fills the registry with unwanted files and data. The unwanted or corrupt files in the registry need to be cleaned out to make sure that the computer is free from error 0×80070570.

Manually cleaning the registry is not recommended because it can be very dangerous. It is possible to lose important files if you manually clean the registry. If you do decide to manually clean the registry, make sure to back up all of your files beforehand.

The most commonly recommended way to clean the registry is to use registry cleaning software. The registry cleaning software deletes unwanted or corrupt files from the registry. This is not the most viable option because the software has to be purchased.

If you decide to clean the registry and error code 0×80070570 still occurs, then one of the files in an installed program might be broken. This can be fixed by deleting the program and reinstalling it. Then make sure the system stays updated when any new updates are available. 

Read More

Error 0x800ccc79

Error 0x800ccc79

Error ox800ccc79 typically appears in Microsoft Outlook when you send messages. The error message can also affect other messaging clients, regardless of the manufacturer. The error message usually states that your e-mail can not be sent due to Simple Mail Transfer Protocol (SMTP) relay blocking. The specific wording of the message may vary, depending on your Internet Service Provider (ISP).

These error messages are becoming more common because ISPs are starting to take action against SPAM. Many ISPs are blocking SPAM by requiring that each user be dialed directly to their system in order to send messages through their SMTP gateway. This in turn affects users who access their e-mail account from another ISP.



The error message can be caused by a few different problems. The error message might appear if you try to send a message through an ISP’s SMTP gateway and you are logged on to a Local Area Network (LAN) that has an Internet gateway. It also might appear if you try to send a message through a different ISP’s SMTP gateway when you already logged on to an ISP. The error message can also occur if you try to send a message and you are using an ADSL or cable modem to get another ISP.



How to Fix Error ox800ccc79



The e-mail client does not cause this error message to appear. As a messaging client, there are no simple solutions for you to perform if your ISP is blocking all SMTP Relay traffic. The only viable option is to contact your Internet Service Provider for assistance.



A majority of the new SMTP e-mail gateway software allows relaying for specific IP addresses. This permits cable modem and ADSL users to continue using their same ISP. The provider of the cable modem or ADSL must give the customer a static IP address. This will let the customer’s e-mail ISP relay for that specific IP address. Corporate customers who access ISPs through their corporate LAN can seek banks of IP addresses to solve their problem.



It is a possibility that your SMTP server is checking whether the domain or the recipient name exists before it sends the message. This could be the case if the error message is random. The error message could be caused by the recipient’s e-mail server being temporarily down or unavailable. Your SMTP server may reject the relay if it can not verify the address. If this is the case, then no action is required. The message will be sent when the receiving server is up again.



How to Fix Error ox800ccc79 on the Microsoft Network (MSN)



The Microsoft Network (MSN) is an ISP that has imposed SPAM blocking. MSN has also set restrictions that cause SMTP blocking errors if the e-mail address in your Internet Account properties does not match the e-mail address in your MSN account. Other ISPs use similar strategies.



To send or receive messages through an additional ISP, LAN, or DSL and other connection devices through MSN, you must set your SMTP settings to secure. Your MSN e-mail server settings for a third-party connection, LAN, or DSL must be set to secure.smtp.email.msn.com.

Read More

How to Solve a Buffer Overrun Detected Problem

How to Solve a Buffer Overrun Detected Problem

Buffer overrun detected problems may occur when unsafe data is permitted by software that is coded in C or C++. This problem can happen in all operating systems, but it is particularly common on Windows-based operating systems. The unsafe data that is introduced externally can exploit vulnerabilities in software or cause program crashes. This can permit malicious software to enter and harm your computer.

Buffer overrun detected error messages should be corrected as soon as possible to ensure that greater security issues do not arise. Follow the instructions below to solve the buffer overrun detected problem.

Instructions to Solve Buffer Overrun Detected Problem

There are a few steps to follow in order to fix the buffer overrun detected problem. The skill level of this solution is considered moderate, and it should be able to be performed by most users. These steps can only be performed on Windows Vista, Windows 7, or Windows XP.

Follow these steps to fix the buffer overrun detected problem:

   1. First you need to download the latest security patches, service patches, and hotfixes for your version of Windows. You can do this through the Windows Update service. There are a couple steps to follow to download these patches.

a. If you have Windows XP, then click on Start, All Programs, Accessories, then Windows Update. If you have Windows Vista or Windows 7, click on Start then Windows Update.

b. Select all of the important/critical downloads. Wait for Windows to download and install these updates. You may be prompted to restart your computer several times, depending on how many updates are available.

   2. If it is available, download and install a newer version of the non-Microsoft software. You can do this by accessing the integrated Check for Updates feature, or by visiting the software vendor’s website and installing the latest version.
   3. If your firewall is not currently enabled, then install or turn on your firewall. You can switch on the Windows Firewall by following these steps:

a. Click on Start and then Control Panel.

b. Click on Classic View in the left column if applicable. Double-click on Windows Firewall.

c. If you use Windows Vista or Windows 7, then click Turn Windows Firewall On or Off in the left column. Then select On or Turn on Windows Firewall then OK. If you use Windows XP, then in the General tab click On.

After your firewall is enabled, it should block the ports that the potential buffer overrun exploiters will request when they transmit malicious data.

How to Solve Buffer Overrun Detected Problem: Microsoft Visual C++ Runtime Library

CyberLink Media Service, or Clmlsvc.exe, scans system files for new media files. If Clmlsvc.exe comes across a path that is more that 255 characters long, then it overflows the buffer. When this happens, you will see the following message on a computer that runs Windows Vista:

“Microsoft Visual C++ Runtime Library
Buffer Overrun detected!
Program: <program path>\CLML\CLMLSvc.exe

A buffer overrun had been detected which has corrupted the program’s Internal state. The program cannot safely continue execution and must now be terminated.”



This issue can occur when you install an application or install a Windows Vista service pack. It can also happen when you install a software update using Windows Update or Microsoft Update. The error could also occur when you upgrade your computer to Windows 7 from Windows Vista.



If you are performing one of the actions listed above, then the error message can be safely ignored. For example, if the error message comes up during the installation of Windows Vista Service Pack 2 (SP2), then you can click on OK to close the error message box. The installation of Windows Vista SP2 will continue and SP2 will be installed correctly.

Read More

How to Solve “Windows Installer Service Could Not Be Accessed”

How to Solve “Windows Installer Service Could Not Be Accessed”


Windows Installer is a very important component of all Windows operating systems that is used to install, uninstall, and support applications and software. If the Windows Installer is corrupted or if the service has stopped for an unknown reason, then an error message comes up. The error message typically appears as: “The Windows Installer Service could not be accessed. This can occur if you are running Windows in safe mode, or if the Windows Installer is not correctly installed. Contact your support personnel for assistance.”

The error message may happen if you are using Windows XP in Normal mode and the Windows Installer Service in Windows XP is damaged or unregistered. It can also occur if the default authentication level is set to None in the DCOM permissions, and the default Impersonation level is on Anonymous. The error might also occur if the Windows Installer is attempting to access a folder or registry key that the system account does not have Full permissions on, but this occurrence is only NTFS-specific.



Methods to Fix “Windows Installer Service Could Not Be Accessed”



There are five specific methods to fix the error message: “Windows Installer Service Could Not Be Accessed.” The method you use depends on the specific issue. Before you use these methods, verify that you have the service pack installed. For Windows 2000, SP2 should be installed. For Windows NT 4.0, SP6 should be installed. The methods may not be effective if the appropriate service pack is not installed. Below is a list and description of the five methods used to fix the error message.



Method 1: Unregister and re-register the Windows Installer



   1. Click on Start, then click Run. Type MSIEXEC /UNREGISTER and then click OK. It may look like nothing happens at this stage.
   2. Click on Start, then click Run. Type MSIEXEC /REGSERVER and then click OK. It still may look like nothing happens, or you may see an hourglass.
   3. The method is complete. Attempt to use your Windows Installer-based application again.



Method 2: Verify the DCOM Permissions



   1. Click on Start, then click Run. Type dcomcnfg and then click OK.
   2. Go to the Default Properties tab. Click Connect in the Default Authentication Level list. Click Identify and then click OK in the Default Impersonation Level list.
   3. Click on Start, then click Run. Type explorer /select, %windir%\system32\msisip.dll and then click OK.
   4. Rename the Msisip.dll file to Msisip.old.
   5. Reinstall the Windows 2000 Service Pack 3.



Method 3: Give Full Control Permission to the SYSTEM Account



   1. Start Windows Explorer. Right-click your computer’s root hard drive. Then click Properties.
   2. Click on the Security tab. Then click on Add.
   3. Click the SYSTEM account in the Select Users, Computers, or Groups dialog box. Click on Add, and then click on OK.
   4. Click to select the Full Control check box under Allow. Then click OK.
   5. Click the TEMP folder and confirm that the SYSTEM account has full control.



Important Note for Method 4 and Method 5



Method 4 and Method 5 both entail using the registry. It is extremely important to back up the registry before completing these methods because there is a possibility that all of your files will be deleted when modifying the registry. If you back up the registry, then your files will be safe in case of an error.



Follow these steps to back up and restore the Windows registry:



   1. Click on Start, then click Run. Type regedit into the Open box. Click OK.
   2. Click on this registry hive: HKEY_CLASSES_ROOT.
   3. Click on Permissions on the Edit menu.
   4. Add SYSTEM to the Group or User Names list if it is not listed already. Then click Add.
   5. Verify that the local computer name is in the From this Location box.
   6. In the Enter the Object Names to Select box, type in system. Click OK.
   7. In the Group or User Names list, click on SYSTEM.
   8. Under Allow in the Permissions for SYSTEM box, select the Full Control check box.
   9. Click on Apply. Click OK. Exit the Registry Editor.



Method 4: Verify the Registry Permissions



   1. Click on Start. Click on Run. Then type Regedt32.
   2. Follow these steps for each of the registry hives:

a. Select the hive.

b. For Windows 2000 and Windows NT 4, click on Permissions on the Security menu. For Windows XP, click Permissions on the Edit menu.

   3. Confirm that the SYSTEM account has been added and that the account has Full control. If the SYSTEM account does not have Full control, then add the SYSTEM account with Full control.



Method 5: Fix the Broken Security Key for the MsiServer Service



   1. Start up the computer by using Windows 2000.
   2. Click on Start. Click Run. Type regedit.exe.
   3. Rename the key below to Old_Security: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\MSIServer\Security
   4. Restart your computer.
   5. Run Instmsiw.exe for installer 2.0 again.

Read More

New Monitors can give life to an older PC

New Monitors can give life to an older PC



    If you want to upgrade your computer, the new monitor is the easiest way to upgrade your computer, because if you have old monitor with new PC, your monitor slow down the system to download image on the screen. The main change with new monitor is the increased screen resolution, fast refresh rates in which a monitor will refresh a image on the screen.

If you want to change the refresh rate of your monitor, Right click on Desktop > Properties > Settings then open Advanced options. Here on the Monitor tab, go to Refresh Frequency list, Here you can change your Monitor frequency with new refresh rate. The default frequency setting of old monitor is 60 Hertz, but your monitor may support more than 60 hertz. First check your monitor manufacturer documentation about your monitor supports. The higher refresh rate reduces the flicker problem on your screen.

Read More

No NTFS Floppies

No NTFS Floppies

 

    Windows XP has never supported NTFS with floppy disks because floppy disks are too small in size for NTFS data structures. If your are using Windows XP and ready to format floppy disk, first right click on drive A, then the only option you will find FAT format.

    If your system uses any file system like FAT , FAT32  and NTFS, but you can  format your floppy  using FAT only.

Read More

How to Turn Your Num Lock On Forever?

How to Turn Your Num Lock On Forever?

    You can set your Num Lock to stay on by default when you logon your system.

    There are two different techniques to set Num Lock stay on by default.

        *          If you can use Registry Editor correctly then Click on start button and type Regedt32.exe in Run command. Here Navigate to HKEY_USERS\.Default\Control Panel\Keyboard and change the value for InitialKeyboardIndicators from 0 to 2.
        *          You can do same by configuring the script to change the NUM LOCK state. Click Start button and then open Notepad. Copy the giving code and paste in Notepad.

           set WshShell = CreateObject("WScript.Shell")

           WshShell.SendKeys "{NUMLOCK}"

          Now save this file with name "num.vbs" must including the quotes. At the end copy this file to user startup folder. The path for this folder is Documents and Settings\All Users\Start Menu\Programs\Startup.

          Now restart the computer. Num Lock should come on and stay on.

Read More

How to Close All Windows Programs quickly?

How to Close All Windows Programs quickly?


    A cool tip to minimize and maximize all your active windows programs. You can do all using your mouse, but if you want to do this with keyboard then simply press Windows key+M to minimize all active programs and later maximize it using Windows key+Shift+M.

    If you want to minimize the all active windows programs one by one then use the shortcut  by pressing Alt+Space+N keys and sequentially maximize the active windows programs using shortcut  Alt+Space+X keys.

Read More

How to Fix the Unmountable Boot Volume Error Message in Windows XP?

How to Fix the Unmountable Boot Volume Error Message in Windows XP?

A common error that occurs with the Windows XP operating system (OS) that results in a system crash is the unmountable boot volume error message. When the error occurs, it is an indication the OS is having difficulty starting or booting from the computer’s “C” drive. Due to the maturity of the Windows XP OS, the problem can be troubleshot and corrected without having to enlist professional assistance in most cases.

The unmountable boot volume error is commonly thrown when a hard drive has been connected with the wrong IDE cable. This can occur when changing out old hard drives on computer’s still running Windows XP when using a standard 40-wire connector cable to connect an UDMA (Ultra Direct Memory Access) drive. Additionally, if the computer’s BIOS settings are configured to force the PC to use the faster UDMA modules, the error can occur requiring you to reconfigure the BIOS to load the default, “fail-safe” settings. Finally, a corrupted BOOT.ini file located in the root directory of the computer file system or boot drive can result in the error being thrown.unmountable boot volume windows xp fix How to Fix the Unmountable Boot Volume Error Message in Windows XP?
Steps to Fix the Unmountable Boot Volume Error Message in Windows XP

Step 1 – Restart the computer with the Windows XP boot disks inserted into the CD/DVD drive after verifying the correct hard drive IDE cable is being used on your computer.

Step 2 – At the Windows XP Welcome screen, press the “R” key to initiate the Windows XP Recovery Console Repair Utility application.

Step 3 – On multiple-boot capable computers, choose the Windows XP installation requiring repair on the subsequently displayed screen.

Step 4 – If prompted, enter the administrator password for the computer. If no prompt is displayed, select the default menu options to proceed with the repair.

Step 5 – Enter “CHKDSK/R” at the DOS command prompt followed by pressing the “Enter” key.

Step 6 – Enter “exit” at the DOS prompt followed by the pressing the “Enter” key after the CHKDSK utility finishing running on your computer.

Step 7 – If the error is thrown upon reboot, repeat steps 1-4. Then, enter the “fixboot” command at the MS DOS prompt. The FIXBOOT command will then write a new partition boot sector to the Windows system partition.

Step 8 – Restart your computer and the Unmountable Boot Volume Error will be corrected.

Read More

Quick Format Vs Default Format

Quick Format Vs Default Format


Today tip about formatting your Hard disk partitions. When you ready to format you partitions, you have two methods to format a partition, you can work with default formatting and other quick format method.

When you first time format your system partition, you should use default method. This is slow and low-level formatting but with this method you can remove all data from the partition as well as the hard disk is scanned for bad sectors. Here you can fix your system bad sectors.

If you select the quick format method, you can save time but you can remove only data from the partition and does not scan the disk for bad sectors. If you sure about your hard disk health then quick format should be fine to remove data with in short time.

Read More

Using REGEDIT With Safety

Using REGEDIT With Safety, Computer Tips, Registry backup

Make sure before modifying your system Registry about its backup, because Registry contains all information how your system runs. This backup will help you to restore Registry in case any problem occurs after modifying. Learn how you can Export and Import Registry File Before Editing?

You can backup the whole Registry and also its subkeys.
Click Start Button then type regedit in Run box and click Ok button. Here you can export the whole Registry or you can locate the required subkeys that contain the information that you want to edit.

Go to File menu option then click on Export option for backup and save it with on any your system drive with .reg extension and you can restore this backup going File menu using import option.

Read More

Removing Add/Remove Programs Entries From RegEdit

Removing add - Programs Entries From RegEdit

Generally we use Add/Remove programs option in Control Panel to remove any unwanted program from our computer. Normally this may be due to poorly designed uninstaller with this program. That is why some programs may not be removed properly and a reference to this program remains in the computer registry. This reference in registry may be creating problems to run your computer smoothly. Here you need to delete this reference to edit your computer registry using RegEdit editor.

    *      First go to Start button and open Run dialog box. Type here RegEdit and press Enter.
    *      Now in editor Navigate to the given path
    *      HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall.
    *      Here locate the entry created by your program with its name and select that entry from the list on the left panel and delete its key.
    *      Close the Registry Editor and restart your computer, the program will be removed from your computer permanently.

Read More

Safer Registry Editing

Safer Registry Editing - How to edit Registry tips and Tricks


Make sure before modifying your system Registry about its backup and you need to know how to organized the registry, how to perform the basic editing, because Registry contains all information how your system runs. This backup will help you to restore Registry in case any problem occurs after modifying. Learn how you can Export and Import Registry File before Editing?

You can backup the whole Registry and only Registry subkeys also.
Click Start Button then type regedit in Run dialog box and click Ok button. Here you can backup the whole Registry or you can locate the required subkeys that contain the information that you want to edit.

Go to File menu option then click on Export option for backup and save it with on any your system drive with .reg extension and you can restore this backup going File menu using import option.

Read More

Task Manager running but hidden from view

 Task Manager running, information about programs and processes

If you are using Windows Task Manager to display the information about programs and processes that are running on your computer. You can start your Windows Task Manager with pressing Ctrl+Alt+Delete keys or with pressing Ctrl+Shift+Esc keys.

To keep Task Manager hidden when it is minimized.

    *      First open it by pressing Ctrl+Alt+Delete keys then go to Options menu and click on Hide When Minimized.
    *      You can easily restore it, if you click on the icon of Task Manager that will appear in taskbar near the time display.

Read More

Write A Batch File To Start Program In Startup

Write A Batch File - start computer applications automatically

You can start your computer applications automatically and control the sequence of the programs when your computer comes up.

Here we consider you want to run three different applications (WordPad, calculator, and notepad) and minimized automatically with sequence at windows startup. However, you can write a batch file to do the job for you. Open any text editor like notepad and type the following command.

start /min wordpad.exe start /min calc.exe start /min notepad.exe

Now choose the option, Save As to save this file with .bat extension. For example filename.bat.

Now Right- click on Start button and choose open > Double click Programs > here open Startup folder. Now drag your .bat file in the Startup folder and close the dialog box.

Next time When you restart the computer, WordPad, Calc will start first and then Notepad. You won't see the batch file run because you told it to run minimized.

Read More